Harley Davidson V-Rod Forum banner

1 - 20 of 21 Posts

·
Registered
Joined
·
18 Posts
Discussion Starter #1
Hey guys,
I'm still new to this Bike and Forum, and I am SURE this has been done, but I thought I'd post a pic anyway. Three small screws remove it.

Just thought it looked cooler and satisfies my obsession with spinny things.
 

Attachments

·
Throttle Happy!
Joined
·
797 Posts
Hey guys,
I'm still new to this Bike and Forum, and I am SURE this has been done, but I thought I'd post a pic anyway. Three small screws remove it.

Just thought it looked cooler and satisfies my obsession with spinny things.
Cool, also saw this the other night at a local bike show...I like it.
 

·
Registered
Joined
·
18 Posts
Discussion Starter #3
Hey 09,
I'm near Waterbury, Where in the NE are you?
 

·
Throttle Happy!
Joined
·
797 Posts
Hey 09,
I'm near Waterbury, Where in the NE are you?
Enfield, about 15 minutes north of Hartford. Starting to see more V-Rods and even some F's locally. It's good to see! Would love to set up an all V-Rod only ride early this fall. We all could meet in the middle of the state like West Farms Shopping mall and ride from there. Could be fun...
 

·
Registered
Joined
·
18 Posts
Discussion Starter #5
Definitely, keep my posted!!
 

·
Registered
Joined
·
821 Posts
Looks cool. Any problems with dirt or water getting in there?
 

·
Registered
Joined
·
18 Posts
Discussion Starter #7
Don't know yet. Just did it like an hour ago. The cover is not a water/air tight seal to begin with, so I don't think it will be an issue.
Think about an open primary on an EVO, and there is clutches in that one!
 

·
Registered
Joined
·
18 Posts
Discussion Starter #8
If I wasn't scared of screwing it up, I would cut out the center piece too.
 

·
Registered
Joined
·
821 Posts
Don't know yet. Just did it like an hour ago. The cover is not a water/air tight seal to begin with, so I don't think it will be an issue.
Think about an open primary on an EVO, and there is clutches in that one!
Never saw one of those, but I'll take your word for it. I hope it works out and it's definitely something I'd like to try.
 

·
Throttle Happy!
Joined
·
797 Posts
If I wasn't scared of screwing it up, I would cut out the center piece too.
Now that's what I was thinking! With a powder coated pulley behind it, that would look cool! Steady with that Dremel tool :D
 

·
Trouble Maker
Joined
·
1,078 Posts
Give me a couple days and ill let you see mine. I got my 26 tooth pulley powder coated and the cover too. I haven't put the cover on yet. Ill try to do it tomm. Jim
 

·
Fat and Fast
Joined
·
223 Posts
I would be up for the ride as well, count me in. Im in middletown.
 

·
Registered
Joined
·
18 Posts
Discussion Starter #13
OK, I succumbed to the peer pressure. I'll be hacking out the center tomorrow... Wish me luck. I might install some mesh in place too, don't know yet.
 

·
TRANNY KILLER :)
Joined
·
14,572 Posts
I've hacked two now.... here's my latest
 

Attachments

·
Registered
Joined
·
18 Posts
Discussion Starter #15
OK, it is about done here is what I came up with. I think it looks cool, just needs some more polishing...

(disregard the melted boot prints on my pipes ;-( )
 

Attachments

·
Pat (Patrick!)
Joined
·
11,222 Posts
Nice look!
 

·
Registered
Joined
·
18 Posts
Discussion Starter #17
Thanks!
In case you were wondering... I had this laying around my garage, so I used it...
 

Attachments

·
Registered
Joined
·
294 Posts
i have an extra pulley cover from my 09 vrscf if anyone needs it
 

·
Pat (Patrick!)
Joined
·
11,222 Posts
1 - 20 of 21 Posts
Top