Signal stabilizer - 1130cc.com: The #1 Harley Davidson V-Rod Forum
» Sponsors
Go Back   1130cc.com: The #1 Harley Davidson V-Rod Forum > V-ROD Discussions > V-ROD Technical
New User? Register - Forgot Password

Reply
 
Thread Tools Display Modes
Old 05-22-2019, 12:30 PM   #1
Jberes
Registered Full
 
Join Date: May 2019
Posts: 6
Feedback Score: 0 reviews
Signal stabilizer

I have an 07 night rod special and Iím trying to wire in my signal stabilizer but canít seem to get it working. Can any tell me where to posi tap the wires into? Or pictures. Iíve tried the male end of the signal harness right before the rear signals. Thanks..
Jberes is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 05-22-2019, 01:31 PM   #2
stever975
Super Moderator
 
Join Date: Nov 2004
Location: Gaithersburg, MD
Posts: 6,248
Images: 31
Feedback Score: 1 reviews
Quote:
Originally Posted by Jberes View Post
I have an 07 night rod special and Iím trying to wire in my signal stabilizer but canít seem to get it working. Can any tell me where to posi tap the wires into? Or pictures. Iíve tried the male end of the signal harness right before the rear signals. Thanks..
Do you mean a turn signal "load equalizer"?

If so, it should have two inputs and a ground. One input should go to a V = violet wire and the other should go to a BN = brown wire that are fed by the TSM/TSSM/HFSM (turn signal/security module) pins 5 & 6 respectively.

These wires run from the TSM/TSSM/HFSM to the front and rear turn signals. On a 2007 VRSCDX the easiest place to find these is under the passenger seat at the TSM/TSSM/HFSM.

You say you tried at the male end of the rear turn signal harness. That should be a 6-place Multilock connector and the turn signal feeds are in positions 3 and 5 with grounds at positions 2, 4, and 6. The load equalizer inputs should go to positions 3 and 5 and the ground should go to 2, 4 or 6 (all are equivalent).
stever975 is offline   Reply With Quote
Old 05-22-2019, 01:40 PM   #3
Jberes
Registered Full
 
Join Date: May 2019
Posts: 6
Feedback Score: 0 reviews
Okay thanks. And yeah it’s a load equalizer, there’s also a blue wire that come with it do you know where that goes? I’ve tried connecting it to the blue one on the female end of the harness but didn’t work.
Jberes is offline   Reply With Quote
 
Old 05-22-2019, 07:46 PM   #4
RustyG
Lifetime Premium
 
RustyG's Avatar
 
Join Date: May 2004
Location: Central Fla
Posts: 11,176
Images: 99
Feedback Score: 11 reviews
Didn't your load equalizer come with instructions? What brand is it. Might help to know that.
__________________
Regards,

John
Everything is JMHO. Accuracy is not assured.
Quote:
Originally Posted by Mark Twain
The more I know about people the better I like my dog. -
2007 VRSCX 0461 / 1400
2003 VRSCA Ė Gone but not forgotten.
2002 Road King Classic
RustyG is offline   Reply With Quote
Old 05-22-2019, 07:49 PM   #5
Jberes
Registered Full
 
Join Date: May 2019
Posts: 6
Feedback Score: 0 reviews
Yah sorry.. it’s the custom dynamics universal signal stabilizer.. and the instructions aren’t very helpful
Jberes is offline   Reply With Quote
Old 05-22-2019, 09:42 PM   #6
Jberes
Registered Full
 
Join Date: May 2019
Posts: 6
Feedback Score: 0 reviews
the wiring harness I’m holding is to the rear signals. Is this where I posti tap into with the signal stabilizer?
Attached Thumbnails
Click image for larger version

Name:	A1375AE4-550C-4387-9677-084D8ADA3D15_1558575712046.jpg
Views:	28
Size:	452.7 KB
ID:	532497  
Jberes is offline   Reply With Quote
Old 05-23-2019, 06:36 AM   #7
stever975
Super Moderator
 
Join Date: Nov 2004
Location: Gaithersburg, MD
Posts: 6,248
Images: 31
Feedback Score: 1 reviews
Quote:
Originally Posted by Jberes View Post
the wiring harness Iím holding is to the rear signals. Is this where I posti tap into with the signal stabilizer?
Yes that's the 6-place Multilock connector I mentioned above. The V and BN wires feed the turn signals, the blue feeds the running lights and the blacks are all grounds. I just read these instructions from Custom Dynamics for their Signal Stabilizer (I added comments in italics):
  1. Make sure bike power is off. (Remove MAXI fuse.)
  2. Locate wires going to rear directional lights. If a Run-Brake-Turn module is installed, Signal Stabilizerô must go before Run-Brake-Turn module. (the wires you need are in the 6-place Multilock connector that feeds the rear turn signals.)
  3. Attach Purple wire from Signal Stabilizerô unit to left side rear directional wire using Posi-Tapô connectors supplied with kit.
  4. Attach Brown wire from Signal Stabilizerô unit to Right side rear directional wire using Posi-Tapô connectors supplied with kit.
  5. Attach Black Wire from Signal Stabilizerô unit to ground wire in wiring harness using Posi-Tapô connectors supplied with kit.
  6. Attach the Blue Wire from Signal Stabilizerô unit to constant power or running light wire in harness using PosiTapô connectors supplied with kit.
  7. Before turning power on, make sure the load switch on the side of the stabilizer is in the ďnormalĒ position. (See next page for Diagram). (Before step 8. below I would perform a turn signal "load learn" procedure:
    Replace MAXI fuse and then disconnect battery negative for at least 1 minute and then reconnect it.
    turn ignition switch OFF-ON
    activate left turn signal lamps for 4 (or more) flashes
    activate right turn signal lamps for 4 (or more) flashes)
  8. Turn key on and test turn signal, running lights, and brake lights for proper operation. If you experience fast flashing from the turn signals, turn the key off, move the recessed switch on the side of the stabilizer to the ďhighĒ position (see diagram on next page), use a small screwdriver or similar object to move the switch. Repeat this step once the switch is moved.
  9. Test Alarm for proper operation, if equipped.
stever975 is offline   Reply With Quote
Old 05-23-2019, 08:37 AM   #8
Jberes
Registered Full
 
Join Date: May 2019
Posts: 6
Feedback Score: 0 reviews
Okay thanks for the help. The stabilizer must be broke. I’ll try n return it. I’ve tried a few times in this spot. And decided to try the front.. now my headlight and front signals don’t work , hopefully I just unhooked something putting it back together . will have to look at it again when I get home from work.
Jberes is offline   Reply With Quote
Old 05-23-2019, 08:50 AM   #9
stever975
Super Moderator
 
Join Date: Nov 2004
Location: Gaithersburg, MD
Posts: 6,248
Images: 31
Feedback Score: 1 reviews
Quote:
Originally Posted by Jberes View Post
Okay thanks for the help. The stabilizer must be broke. Iíll try n return it. Iíve tried a few times in this spot. And decided to try the front.. now my headlight and front signals donít work , hopefully I just unhooked something putting it back together . will have to look at it again when I get home from work.
Technically, it doesn't matter if you hook to the front or back. The front and back signals are fed by the same outputs from the TSM/TSSM/HFSM. The only distinction is left or right.
stever975 is offline   Reply With Quote
Old 05-23-2019, 09:46 AM   #10
Jberes
Registered Full
 
Join Date: May 2019
Posts: 6
Feedback Score: 0 reviews
Yeah I know. That’s why I’m thinking I just bumped something loose. Thanks again for the help!
Jberes is offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
How to install Customdynamics turn signal stabilizer G4ses How-To 6 08-10-2015 02:08 AM
Signal stabilizer/left turn signal problem Gunboy V-ROD Technical 4 03-31-2013 08:05 PM
Signal; Stabilizer Question Koa04 V-ROD General 2 08-18-2009 10:02 PM
Custom Dynamics signal stabilizer G4ses V-ROD Technical 6 01-09-2008 04:38 PM

Powered by vBadvanced CMPS v3.2.2

All times are GMT -5. The time now is 06:35 PM.



Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Garage Plus vBulletin Plugins by Drive Thru Online, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Motorcycle News, Videos and Reviews
Honda Grom Forum strong>Kawasaki Z125 Forum Harley Davidson Forum Honda 600RR Forum Kawasaki Forum Yamaha R6 Forum Yamaha FZ-09 Forum
1199 Panigale Forum Honda Africa Twin Forum Roadglide Forum Honda CBR1000 Forum Vulcan Forum Yamaha R1 Forum Yamaha R3 Forum
Ducati Monster Forum Harley Forums Honda CBR250R Forum ZX10R Forum Star Raider Forum Yamaha Viking Forum
Suzuki GSXR Forum V-Rod Forums Honda Shadow Forum Kawasaki Motorcycle Forum Star Warrior Forum KTM Duke 390 Forum
SV650 Forum BMW S1000RR Forum Honda Fury Forum Kawasaki Versys Forum Drag Racing Forum Ducati 899 Panigale Forum Ducati 959 Panigale Forum
Suzuki V-Strom BMW K1600 Triumph Forum Victory Forums Sportbikes BMW NineT Forum
Volusia Forum BMW F800 Forum Triumph 675 Forum MV Agusta Forum HD Street Forum
Yamaha Motorcycles Honda Vultus Forum HD LiveWire Forum Ninja H2 Forum
BMW Scrambler Forum Ducati Scrambler Forum