Harley Davidson V-Rod Forum banner

Reaction score
15

Marketplace Rating
(5.0 - 8 reviews)

Profile posts Latest activity Discussions Buy & Sell Reviews Media Showcase items About

  • · Registered
    Joined
    ·
    95 Posts
    Knock on wood, I think we got it. Gonna put some miles on it then decide if a trip to the dyno shop is needed? It seems to be running pretty good might be running a bit hot or its just the exhaust being right next to my leg?LOL

    · Registered
    Joined
    ·
    95 Posts
    Hey there, just an update got the parts back from track reinstalled them fixed the oil leak now I can't seem to get the fuel rail to stop pissing fuel under pressure? I have changed all the 0rings & as soon as I put the power to it it pisses fuel??? Any tips
    Thanks
    Bill

    · Registered
    Joined
    ·
    95 Posts
    Hey there, hoping to pick your brain. I purchased a Trask kit for my 09 muscle. I went step by step and installed it with the Thundermax auto tuner. Bike fired right up no codes, rode it for a few short trips then took it on a 40 mile highway ride after that all the ceramic coating on the kit began peel off? I contacted Trask & they are trying to figure out what happened with the ceramic coat they are going back & forth with Jet hot to figure out how they are going to fix the issue but in the meantime I noticed a small oil leak my mechanic is telling me it looks like the head gasket on the front cylinder is leaking! WTF 80 miles on this kit I got peeling paint & leaking oil! Could I have installed something incorrectly causing these issues? The bike hesitated a few times & I just figured the auto tune would sort out the tuning? Are head gasket issues prone to these systems? How big of a job it it to replace the gaskets. As I said earlier Thank you for any advice! Bill

    · Registered
    Joined
    ·
    42 Posts
    Thanks for the information. When I check the triple sprocket, do I need to drain the oil first? This is probably ridiculous but I'm not very mechanically inclined. I opened the side of it this weekend and some oil came out and so I shut it and bolted it back on again quickly. Thanks for the info.
    Joe

    · Registered
    Joined
    ·
    69 Posts
    hey it's Jake out in Sylvania, wanted to try and put a 260 on an 02 vrod, got a shop locally you'd recommend to get this done at? - Jake

    · Premium Member
    Joined
    ·
    330 Posts
    $$$$ did you get the shims back and how much do I owe you for everything ?

    I can't say thanks enough..

    · Registered
    Joined
    ·
    310 Posts
    Rod,
    Please advise me on which cams I should,use for my stock 1130? I assume you are ordering the stage Ii intake and exhaust due to less,overlap (CamKing's explanation). Thanks L

    · Registered
    Joined
    ·
    310 Posts
    Rod
    Even if these cams were only good for 10 or 12 HP, this would be a pretty good deal at $500 bucks! I assume we would need to change the map as well? Please confirm my assumptions and I will commit with Doug on the group buy. Thanks, L

    · Gunboy
    Joined
    ·
    14 Posts
    Hey rod,
    I finished the Dutch customs led / Gravestarr faceplate mod. Thanks for the video and the encouragement I did as u said and took my time. The only issues I had was the light on the tach wouldn't light up but after a few minutes on the road it came on as I hoped and hasn't gone out again. Also, I'm not too confident the needles are showing true on the tac and the gas.... I reset them along the pencil marks and when I would test the function after I would turn ignition off the needles would turn to home but then after a few seconds start to move past the zero mark on tach and past e on gas gauge I set and reset over and over again and it still doing it. The tach comes to zero when I fire it up but seems like rpms aren't marking where they used to. After I filled up the gas needle didn't quite make it to full (which is normal but after a few minutes needle always corrects and marks correctly). What do u think buddy
    Sal

    · down under
    Joined
    ·
    31 Posts
    Hi all, help needed for a good forced induction tuner in oz on a Trask turbo set up on my 2012 night rod. Tuner is power commander v pti with 2 bar map sensor. Any help would be greatly appreciated. Cheers

    · Registered
    Joined
    ·
    496 Posts
    What would be the best seat to add to my 2011 Vrod Night Rod that will give my passenger more comfort than now and still be able to work if I change my rear fender?

    · Registered
    Joined
    ·
    1,886 Posts
    Hi RSC ,maybe you could help me with a project I`m doing,I have a 2008 vrscawa (abs) and it has the wire front wheel ,I just got a front wheel (slotted) from a 2007 vrscaw without abs what would I need to do to make this work,if you could help me it is much appreciated-Noel

    · Registered
    Joined
    ·
    1,886 Posts
    Hi RSC how are you feeling lately,hope you are doing well ,just thinking of you and keeping you in my prayers-Noel

    · Premium Member
    Joined
    ·
    811 Posts
    Rod finally got the engine guard mounted,there was no threads in that center hole so
    I had to tap new threads.The fairing was a bit of a fiight,as things changed somewhat
    with the new 6 deg.trees.I managed to make it work.Sure wished you were closer to Mi
    I could keep you real busy. I'm starting to get bad vibes with vmod.Four months wait is
    quite a bit forr a hjead gasket don't you think? Next time something come up I'll give you a call. Roge
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Top